How to: Install a touchscreen in your netbook

Tired of your netbook's tiny touchpad? Here's how to install a touchscreen.

Is your netbook envious of touch-driven devices? You can't turn your netbook into an iPad, but you can retrofit it with a touchscreen and avoid the tiny touchpad.

WARNING: Only skilled or daring hardware hackers should attempt this process. Voiding the warranty is the least of your concerns; you'll have to solder parts together, cut away some of the laptop's plastic housing, and otherwise make permanent changes that you can't undo. Make the wrong move, and you'll break the laptop. We are not responsible for anything that goes wrong with your PC as a result of your following our instructions.

If you know your way around a soldering iron and are willing to strip your netbook down to its last screws, however, you'll likely succeed at this project. It's a straightforward process, even though it's too daunting for beginners.

Install a Touchscreen in Your Netbook

I installed a touchscreen into a Dell Mini 10. Follow my steps if you have that exact netbook, or read through to get a sense for how to approach your own model. The general process will be the same, and I include many tips that I picked up along the way. Read through to the end before getting started.

Tool Time

First, line up all the parts and tools you'll need to install a touchscreen.

Of course, the touchscreen panel itself is the centerpiece. This clear overlay sits on top of your current LCD. Usually it's sold in a kit with a USB controller board. I couldn't locate any shops that keep these in stock, so I turned to eBay and a Hong Kong importer.

Pick a touchscreen panel that matches the size and aspect ratio of your screen. I bought a 10.1-inch model that fits the Mini but was designed for an Acer Aspire One, for US$90. These panels are usually resistive--that is, responding to pressure--not the capacitive type, which recognizes your skin. Single-touch panels are also more common; get a capacitive, multitouch panel if you can find one, but prepare to pay more.

You'll also need a reliable soldering station. I have the Weller WES51. I can set its temperature to make it hot enough to melt solder without sending excessive heat to the connected parts.

Get a small tip or two for your soldering iron. I have 1/32-inch and 1/64-inch tips. You'll make small joints and surface-mount connections that require a fine point. Also, use some fine solder, with about a 0.02-inch diameter. You'll need to add your own flux, as well; I just brush some on from a jar, but pick whatever kind you like.

You might need some low-gauge wires to extend the touchscreen cabling. If you have a spare USB cable, cut that open to harvest its wires.

If you have the motor control and eyes of a 14-year-old, you might be able to work without magnification. Otherwise, I recommend a lighted, magnifying arm. Buy one from an electronics-parts store such as Jameco, or even from Amazon.

Also, you'll need a Dremel or similar tool to shave plastic from one of the speakers and to lop off a leg under the wrist rest.

Finally, gather the basics: a pair of scissors or a wire stripper, electrical tape, a Phillips screwdriver, and other common tools. Grab a handful of guitar picks to help crack open the case, and tweezers to make fine movements. Also keep a days-of-the-week pillbox or two to store screws in separate compartments. Put the screws from each step in their own compartment, and write down where you stored them as you progress.

Get Hacking

Clear off a well-lit workspace, and you can begin the dissection. First, unplug the laptop and remove the battery. Turn the machine upside down on a padded surface to avoid scratches; a big mouse pad works well. Remove the four screws on the corners surrounding the battery cavity.

Install a Touchscreen in Your Netbook

With that battery slot on the edge away from you, remove the four screws along the edge closest to you. Each set of those screws straddles one of the two rubber footpads.

Remove the screw in the center of the laptop. If this screw doesn't fall out, you can push it out after removing the keyboard in the next step.

Install a Touchscreen in Your Netbook

Turn the laptop right side up, and open the screen. Lift the keyboard out from the top edge, along the F-keys. Pivot it over the spacebar edge to access the ribbon cable underneath. Use your fingernails, tweezers, or the dull side of a hobby knife to slide back the tabs next to the ribbon cable; once you've moved those, the cable will be released. Set the keyboard aside.

Join the newsletter!

Error: Please check your email address.
Rocket to Success - Your 10 Tips for Smarter ERP System Selection

Tags notebooksnetbookspc componentstouchscreens

Keep up with the latest tech news, reviews and previews by subscribing to the Good Gear Guide newsletter.

Zack Stern

PC World (US online)
Show Comments


James Cook University - Master of Data Science Online Course

Learn more >


Sansai 6-Outlet Power Board + 4-Port USB Charging Station

Learn more >



Back To Business Guide

Click for more ›

Brand Post

Most Popular Reviews

Latest Articles


PCW Evaluation Team

Andrew Teoh

Brother MFC-L9570CDW Multifunction Printer

Touch screen visibility and operation was great and easy to navigate. Each menu and sub-menu was in an understandable order and category

Louise Coady

Brother MFC-L9570CDW Multifunction Printer

The printer was convenient, produced clear and vibrant images and was very easy to use

Edwina Hargreaves

WD My Cloud Home

I would recommend this device for families and small businesses who want one safe place to store all their important digital content and a way to easily share it with friends, family, business partners, or customers.

Walid Mikhael

Brother QL-820NWB Professional Label Printer

It’s easy to set up, it’s compact and quiet when printing and to top if off, the print quality is excellent. This is hands down the best printer I’ve used for printing labels.

Ben Ramsden

Sharp PN-40TC1 Huddle Board

Brainstorming, innovation, problem solving, and negotiation have all become much more productive and valuable if people can easily collaborate in real time with minimal friction.

Sarah Ieroianni

Brother QL-820NWB Professional Label Printer

The print quality also does not disappoint, it’s clear, bold, doesn’t smudge and the text is perfectly sized.

Featured Content

Product Launch Showcase

Latest Jobs

Don’t have an account? Sign up here

Don't have an account? Sign up now

Forgot password?